Two Ram Baler Model TR-1288-100S

       Revised: 6/06

HYDRAULIC

         Main Pumps                                  298 GPM Total Flow (Regen. System)

            System Pressure                     3200 PSI

            Main Cylinder                          12 In Bore

            Ejector Cylinder                  9 In Bore

            Bale Door Cylinder             8 In Bore

            Precompression Cyl.           8 In Bore (Optional)

            Total Force                               361,900 Lb

            Ram Face Pressure                218 PSI

            Oil Reservoir                           650 Gallon Capacity

                                                                        L&P Wire-Tie or Accent Wire- Tire

ELECTRICAL

            Main Motor                                100 HP, 460 Volt, 3 Phase, TEFC, Special Duty,

                                                                        WYE delta  Starting  Standard

            Cooler Pump Motor              10 HP, 460 Volt, 3 Phase

            Cooler Fan Motor                 3 HP, 460 Volt, 3 Phase

            Strapper Pump Motor          10 HP, 460 Volt, 3 Phase

            Controls                                     Programmable Controller with Diagnostics and Phone Modem

            Photocell                                   Infrared Type

STRUCTURAL

         Length Overall                      36 Ft

            Hopper Opening                        96 In Long x 72 In Wide (W/Lid 90 In. Long x 60 In Wide)

            Charge Box Opening             96 In Long X 57.5 In Wide (W/Lid 90 In Long x 57.5 In Wide)

            Width Overall                         21 Ft 0 In

            Charging Hopper Ht.            7 Ft 6 In (With Lid 13 Ft 1 In)

            Shear Blade                               Knife Steel, Reversible

            Liners                                             Hardox 400 or Equal (Charging Box totally lined w/wear plates)

            Shipping Weight                       46 Tons Approximate (With Lid 50 Tons)

PERFORMANCE

            Bale Size                                       45 In Wide x 30 In High x 62-64 In Length

            Bale Volume                              50 Cubic Feet Expanded (Approximate)

            Cycle Time                                  16 Seconds (No Load – Main Cylinder Only)

            Bale Time                                     130 Seconds (Strapper Time Included) 

                                                                        *(3 Strokes/Bale) Estimated for OCC W/Lid

Material	Material PCF Infeed Density	Bale Weight LB	Density  PCF Baled	Output No Lid Tons per Hr	Output With Lid Tons per Hr
*OCC	2.5 -  4	up to 1400	up to 27	up to 17	up  to 19
*News	6 - 8	up to 1600	up to 32	up to 27	up to 32
*PET	.75 - 4	up to 1250	up to 25	up to 7	up to 9
*UBC	1.5 - 4	up to 1000	up to 20	up to 15	up to 16
*Misc. Aluminum	1 - 2	up to 1700	up to 34	up to 6	NA
*Solid Waste	8 - 12	up to 2400	up to 48	up to 38	up to 38

*Performance Rates, Bale Weights, and Bale Densities Are Subject to Moisture Content, Material Pre-Bale Densities, Feed Rates, And Other Variables in Baling

 

STANDARD FEATURES                                          AVAILABLE OPTIONS

Programmable Controller with Phone Modem                  Pre Compression Lid

Oil Cooler and Oil Heater                                                  Conveyor Controls

Bale Door / Relief                                                                      Feed Hopper Extension with Upper Level Sensor

Across the Line Starting Standard                                                             Contact Factory for other Options

 

Specifications and Design are Subject to Change if, in the opinion of the Manufacturer, the Change is an improvement.